Dual Mode—Two Ways to Use

	Internal Mic Mode The earpiece is designed to be self-supporting in the ear canal, so the earloop is optional. Push the earloop through the earloop holder and adjust for a secure fit.
	BLUmaxx Mic Mode Exceptional clarity in noisy environments. Gives up to 25 dB more noise cancellation of the talker's voice compared to the internal mic.

Important: To ensure optimal performance it is important that the eartip seals the ear canal.

Pairing
Pairing varies by device
The etyBLU headset is discoverable for five minutes after Power On.

• Turn the phone OFF and then back ON.
• Turn on the mobile phone’s Bluetooth function.
• Press and hold the Multi-Function Button (MFB) for 5 seconds.
• The blue LED will flash rapidly when ready for pairing.The etyBLU stays in pairing mode for 5 minutes.
• Activate the search for BT and/or audio devices on the phone
• When the etyBLU is found, the phone will display “etyBLU.” Scroll to it and press OK to confirm pairing.
• If a passkey/password is requested, enter 0000.

Note: Bluetooth transmitter pairing varies. For best results, consult the user instructions for the specific device being paired with the etyBlu. Some mobile phones require a security setting change for automatic headset-phone pairing.

Charging
The etyBLU headset comes with a rechargeable lithium polymer battery. Charge the headset for at least one hour before first use.
Charging time from empty: 2-3 hours
80% charge: 1 hour

Charging with the USB connecter (included)

• Remove the BLUmaxx Mic prior to charging
• Plug the connector into the etyBLU headset as shown.
• Plug USB end of the charging cable into a computer USB port as shown.
• The solid yellow LED will indicate that the headset is charging.
• When charging is complete the yellow LED turns OFF.

Insertion
Important: Sound quality and noise isolation depend on a good eartip seal.

1. Carefully insert the earpiece while pulling up and out on the back of the ear.
2. Twist the earpiece while inserting until outside noise is blocked out.
3. Position the earpiece for best fit and comfort.
4. Flanged eartip: Moistening eases insertion.
5. Foam eartip: Roll down or compress foam eartip before inserting. Hold the eartip in place for about 5 seconds while the foam expands to create a tight seal in the ear canal.

Removal
To avoid discomfort, remove the headset slowly with a twisting motion to gradually break the seal. Open jaw slightly to equalize pressure, because suction can occur when the eartip is removed.

BLUmaxx Connect/Disconnect
NOTE: The BLUmaxx Mic can quickly connect or disconnect without disconnecting a call.

To Connect

1. The plug on the BLUmaxx Mic is designed to connect to the headset only one way. Do not force the plug into the jack. It will connect easily.
2. When the BLUmaxx Mic is connected correctly, the opening at the tip of the microphone is closest to the mouth and the opening at the middle of the mic tip faces away from the mouth.

To Disconnect

1. Grasp the connector and gently remove the BLUmaxx Mic.
2. Keep the BLUmaxx Mic in the storage case for easy access.

Multi-Function Button (MFB)

Power ON	PRESS the MFB for 4 seconds to Power On. Blue LED is solid for one second while powering ON. Blue LED blinks when the headset is ON.
Power OFF	PRESS the MFB for 4 seconds to Power Off. Yellow LED is solid for one second then powers OFF.
Volume	PRESS the Volume UP (+) and Volume DOWN (-) buttons on the side of the headset to increase or decrease volume. The exact number of volume levels is set and maintained by the phone.
Answer a Call	PRESS the MFB once quickly (short press) to answer a call when phone rings.
End a Call	PRESS the MFB once quickly (short press) to disconnect the call.
Reject a Call	PRESS and HOLD the MFB (long press) for one second to reject an incoming call.

The following features depend on phone support:

Redial	PRESS and HOLD the MFB (long press) for one second.
Voice Call	PRESS the MFB quickly (short press) to make a voice call. Voice Call works when the unit is in standby.
Transfer a Call	Double PRESS the MFB (two quick presses to the Handset less than one second) during a call
Call Waiting	PRESS and HOLD the MFB (long press) for one second to put a call on hold to answer another PRESS and HOLD the MFB (long press) for one second to switch between calls PRESS the MFB quickly (short press) to end the current active call
3-Way Calling	Add another caller: Depending on the call status, double press the MFB to add the held call to the conference.