Instructions for Use
For use with iPod and 8•mate | For Use with Other
Bluetooth-Enabled Devices
Note: Fully charge before first use (approximately 2-3 hours).
Charging: LED yellow
Charging complete: LED off
•
8•Mate™ adapter does not require charging.
• Charge the earphones from a computer via the USB cable provided.
Charging
1. Plug USB cable into the USB port on the R earphone.
2. Connect to a computer.
Battery
life: Up to 10 hours
• Low battery warning: LED blinks green when there is one hour left.
• To maximize battery life, remove adapter to avoid iPod battery drain when
iPod is not in use.
When properly sealed, the earphones are self-supporting in the ear canal. Sound
quality and noise isolation depend on a good eartip seal.
Insertion
- View Earphone
Insertion Video
• Pull ear up and back.
• Twist earphone while inserting until outside noise is sealed off.
• Position (rotate) earphones in the ear for the best fit.
• Foam eartips: Roll the foam down, then insert and hold in the ear for 5
seconds.
Removal
• To avoid discomfort, use a slow twisting motion to gradually break the seal.
• Open the jaw slightly to equalize pressure, because suction can occur when
the eartip is removed.
Pairing with an iPod is not necessary.
Earphones
include an 8•Mate™ adapter for iPod, paired at the factory.
Pairing
with another Bluetooth® device:
• Make sure the earphones are OFF.
• Press/hold the POWER button on the R earphone for about 10 seconds.
• The LED on R earphone will rapidly flash green when ready for pairing.
• The earphones will stay in a discoverable mode for five minutes or until
pairing is complete.
• If a passkey is requested, enter "0000"
Note: Bluetooth transmitter pairing varies. For best results, consult the user
instructions for the specific device being paired with these earphones.
Power On
• Press/hold POWER button on the R earphone until LED is on (1-2 seconds).
Note: The POWER button also functions as a PLAY/PAUSE control.
• Select music on the iPod, then press PAUSE.
• Plug in 8•Mate adapter. The LED will blink green.
• Press PLAY on the iPod.
The LED is solid green on both the earphone and adapter when connected.
Power
Off
Press the POWER button on R earphone for 3 seconds until the green LED goes
off.
Auto
Shut Off
If no music is playing, the earphones will turn off after five minutes. To
maximize battery life: Remove 8•Mate adapter to avoid iPod battery drain when
iPod is not in use.
See iPod Models Supported for details.
See About the Filters for details.
• Avoid extreme temperatures, strong impact and water.
• Perspiration can cause the earphones to temporarily stop working, but normal
operation usually returns after the earphones dry out.
• Always leave an eartip on the earphone for shock protection.
• Replace foam eartips regularly.
Flanged eartips:
Clean regularly. Simply wipe off the eartips. If water and mild soap are used,
dry the eartips before reattaching.
Foam
eartips:
Discard dirty eartips and replace with new ones.
Note:
Fully charge before first use (approximately 2-3 hours).
Charging: LED yellow
Charging complete: LED off
• Charge the earphones from a computer via the USB cable provided.
Charging
1. Plug USB cable into the USB port on the R earphone.
2. Connect to a computer.
Battery life: Up to 10 hours
• Low battery warning: LED blinks green when there is one hour left.
When properly sealed, the earphones are self-supporting in the ear canal. Sound quality and noise isolation depend on a good eartip seal.
Insertion
- View Earphone
Insertion Video
• Pull ear up and back.
• Twist earphone while inserting until outside noise is sealed off.
• Position (rotate) earphones in the ear for the best fit.
• Foam eartips: Roll the foam down, then insert and hold in the ear for 5 seconds.
Removal
• To avoid discomfort, use a slow twisting motion to gradually break the seal.
• Open the jaw slightly to equalize pressure, because suction can occur when the eartip is removed.
Bluetooth transmitter pairing varies. When pairing ety8 earphones, follow the instructions for the device being paired with the earphones.
Instructions
for ety8 earphones:
• Make sure the earphones are OFF.
• Press/hold the POWER button on the R earphone for about 10 seconds.
• The LED on R earphone will rapidly flash green when ready for pairing.
• Once the earphones are in fast blink mode, you have five minutes to pair with
the Bluetooth device.
• If a passkey is requested, enter "0000"
Power On
• Press/hold POWER button on the R earphone LED Play/Pause until LED is on (1-2
seconds).
Note: The POWER button also functions as a
PLAY/PAUSE control.
Power
Off
Press the POWER button on R earphone for 3 seconds until the green LED goes off.
Auto
Shut Off
If no music is playing, the earphones will turn off after five minutes.
Volume
Volume adjustments can only be made using the R earphone controls.
• Avoid extreme temperatures, strong impact and water.
• Perspiration can cause the earphones to temporarily stop working, but normal
operation usually returns after the earphones dry out.
• Always leave an eartip on the earphone for shock protection.
• Replace foam eartips regularly.
Flanged eartips:
Clean regularly. Simply wipe off the eartips.
If water and mild soap are used, dry the eartips before reattaching.
Foam
eartips:
Discard dirty eartips and replace with new ones.